Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Fuel gauge is pointing down no matter what
#1
Another new recent problem, my fuel gauge is pointing down no matter what.
So far I've done the following:-

I've used the multi-meter to verify that the signal from the green/black wire (for the gauge needle) beeps at the plug for the sender as it does on corresponding pin (A4) on the big white connector behind the binnacle.  I then kept the multi-meter on the same sender end of the harness and tested each other pin of the binnacle connector expecting to hear another beep from another wire to indicate a short, but there were no other beeps.

I then performed the same test for the light green and orange wire (for the sender light) in the same way to the above, only to find the same outcome.

I'm pleased that there appears to be no short but stumped as to why my gauge is all of a sudden pointing south.  The other gauges are all still running perfectly.

Any input or suggestions would be most welcome.

Thanks in advance

Chris
Regards,

Chris Hawes
DOC 138
Ex owner of VIN 5255 Grey, 5-speed
Reply
#2
I don't understand the technicalities at all Chris.....but when mine developed a fault, about a year ago, we removed the sender and cleaned it up a bit and it been fine since. Not much of a job to try it.
Chris Parnham

Ex RHD Auto's etc.etc

Main Car.. Kia E Niro 4+
Skoda Yetil 4X4.
Toyota Vitz 4X4 1999 (the smallest 4X4 by far!.
1970 Jago Jeep.

DOC Club Historian 
Reply
#3
Would there be a chance that whilst fitting a new pump something has been re-fitted so that its keeping the float pressed down? or been damaged during pump work?
Chris
Membership Secretary DOC UK
2021's DeLorean event: http://www.deloreans.co.uk/forum/showthr...p?tid=6056
VIN#15768 Ex VIN#4584
Reply
#4
What I would do (tell me if I’m out of line here because I’m not yet an owner) is to take the float mechanism out of the tank and try manually moving the float to see if it affects the gauge..... 2 man job of course. (And gently does it)
And I guess if the fuel pump is part and parcel of this, then my idea sucks, unless you can disconnect the pump.

Same thinking as Chris in terms of something jamming the float down, at least if this works you can be sure the float mech is operational.
_________________
DOC #230

VIN 11477 Jan '82
2010 Range Rover V8
2013 Mini Cooper S Works

Tristan J Carroll
Swansea, South Wales
Reply
#5
[Image: hMLyimoqodSVVjy6xLXj0a6QnAtoxhFhMz5GgQ7m...ntcZI=w200]


Through the testing (as per the video I've just uploaded via the thumbnail above) I was able to confirm the issue wasn't the wiring or sender....

I hope this helps anyone else in the same scenario!
Regards,

Chris Hawes
DOC 138
Ex owner of VIN 5255 Grey, 5-speed
Reply
#6
Excellent Video Chris....even I could understand it! Smile
Chris Parnham

Ex RHD Auto's etc.etc

Main Car.. Kia E Niro 4+
Skoda Yetil 4X4.
Toyota Vitz 4X4 1999 (the smallest 4X4 by far!.
1970 Jago Jeep.

DOC Club Historian 
Reply
#7
Top stuff, but why does your tacho needle go all the way around?
Chris
Membership Secretary DOC UK
2021's DeLorean event: http://www.deloreans.co.uk/forum/showthr...p?tid=6056
VIN#15768 Ex VIN#4584
Reply
#8
Great video Chris, thanks for sharing.

Tris
_________________
DOC #230

VIN 11477 Jan '82
2010 Range Rover V8
2013 Mini Cooper S Works

Tristan J Carroll
Swansea, South Wales
Reply
#9
Great spot Chris, I'd noticed that too since [Image: UG2CcMXwHeQgAygbeH6npsie_e-GmMsBFUNR7p2n...avKdU=w200] the conversion.  I now have a much more powerful Bosch 044 fuel pump which is overkill for a stock car.  Whether you start the car straight away or wait a few seconds for the new pump to prime makes no difference to the cranking or starting.  From memory, I think any DeLorean 'remembers' the last tacho reading from when the ignition was last on.  When you turn on the ignition circuit, the tacho then resets back to zero which again I think is the same from stock.  If I wait now for it to prime before turning the key to crank (not that you have to) then the needle flicks to a much higher reading before then moving to the correct start up revs and from there it continues to read accurately.

In summary, some gauges 'remember' their last readings when the ignition is off and it looks like I've added another quirk into the mix Smile
Regards,

Chris Hawes
DOC 138
Ex owner of VIN 5255 Grey, 5-speed
Reply
#10
Quote: From memory, I think any DeLorean 'remembers' the last tacho reading from when the ignition was last on.  When you turn on the ignition circuit, the tacho then resets back to zero which again I think is the same from stock.
Cant argue with that, it was how yours jumped all the way around to the top that was a surprise, I had never seen that before. Must be all that extra power your packing and the cars getting itself ready for it.  ;-)
Looks a superb conversion BTW
Chris
Membership Secretary DOC UK
2021's DeLorean event: http://www.deloreans.co.uk/forum/showthr...p?tid=6056
VIN#15768 Ex VIN#4584
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)