+- The DeLorean Owners Club UK Forum (http://www.deloreans.co.uk/forum)
+-- Forum: GENERAL DELOREAN DISCUSSION (http://www.deloreans.co.uk/forum/forumdisplay.php?fid=2)
+--- Forum: DeLorean Cars or Parts For Sale or Wanted (http://www.deloreans.co.uk/forum/forumdisplay.php?fid=26)
+--- Thread: Trailing arm shims wanted (/showthread.php?tid=1542)
Pages:
1
2
Trailing arm shims wanted - Dan6457 - 09 May 2008
My car is having its wheels aligned next week now Ive put new track rod ends on, so I'd like to go armed with a few shims in case the rears are a bit out. Does anyone have some kicking about that I could borrow and/or buy if I end up needing them?
Cheers.
- Dan6457 - 10 May 2008
I had it aligned this morning and they had shims on the shelf, so I don't need these now.
- Outatime - 10 May 2008
OT: What is the correct allignment details for the D??
xx mm?? or XX degree??
- NickT - 12 May 2008
http://www.deloreans.co.uk/technical/ma ... ntents.pdf
PDF page 12, Manual page 10
3mm toe in PER WHEEL.
Same for front and rear wheels.
Try and get a full geometry done but if not do a 4 wheel to centreline (checking thrust angles) at least.
A 2 wheel alignment, or 2 wheel to centreline is not enough.
NickT
- Dan6457 - 12 May 2008
I had a full geometry check done on saturday. It took 4 shims on one side and 1 on the other to bring the rear into spec. Their computer system had the Delorean on it! My castor was out though which is strange, no way of adjusting that though, but it doesn't seem to be affecting anything. The difference in feel after the alignment is amasing, and the steering wheel is now straight when I go in a staight line which makes a change :wink:
- Chris Williams - 12 May 2008
Dan1986 Wrote:I had a full geometry check done on saturday. It took 4 shims on one side and 1 on the other to bring the rear into spec. Their computer system had the Delorean on it! My castor was out though which is strange, no way of adjusting that though, but it doesn't seem to be affecting anything. The difference in feel after the alignment is amasing, and the steering wheel is now straight when I go in a staight line which makes a change :wink:
Where did you get this done Dan? somewhere local?
Chris
- NickT - 12 May 2008
If it drives nice then enjoy it
As long as you don't get bump steer I would leave it as it is.
You could have a look at:
http://www.deloreans.co.uk/technical/alignment/
if you are interested.
NickT
- Dan6457 - 12 May 2008
Chris Williams Wrote:Where did you get this done Dan? somewhere local?
Chris
This place in Maldon: http://www.super-tyres.co.uk/index.html
They have Delorean on the alignment computer. Its an american system so thats probably why its on there. Really clever system. It works by constantly taking pictures of plates that clamp onto the wheels.
- Chris Williams - 12 May 2008
Dan1986 Wrote:Chris Williams Wrote:Where did you get this done Dan? somewhere local?
Chris
This place in Maldon: http://www.super-tyres.co.uk/index.html
They have Delorean on the alignment computer. Its an american system so thats probably why its on there. Really clever system. It works by constantly taking pictures of plates that clamp onto the wheels.
Cheers Dan
Chris
- Dan6457 - 12 May 2008
![[Image: align1.jpg]](http://www.martinstacey.btinternet.co.uk/delorean/align1.jpg)
![[Image: align2.jpg]](http://www.martinstacey.btinternet.co.uk/delorean/align2.jpg)
- A Van - 13 May 2008
Hi
Shouldnt the toe in be different from stock on the front, because of the lowered springs?
- Dan6457 - 13 May 2008
Why would having lower springs mean the toe should be different?
It showed on the computer that my front camber was more than it should be by a little and that was put down to the lowering springs.
Are you still going to pop over somtime Alastair with that magazine and that?
- bozzzydmc - 13 May 2008
Nice funky wheel trims there
As the car is lowered the camber adjusts slightly..., there are some adjustable lower rear link arms available on cars that need this adjustment due to uneven tyre wear .... mine is still within spec though
- Outatime - 13 May 2008
BTW Dan, just out of interest... how much did they charge you for the allignment of all 4 wheels??
- A Van - 13 May 2008
Hi Dan
I havent forgot, I have just been absolutely stupidly busy with work...I reckon I will be over though within the week.